WEKO3
アイテム
ハイポイドギヤの歯切り誤差検出法
http://hdl.handle.net/10191/5470
http://hdl.handle.net/10191/5470420eb6d9-050a-479e-8a2d-06c54f535fe2
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
4_0003.pdf (1.0 MB)
|
|
| Item type | 会議発表論文 / Conference Paper(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2008-04-08 | |||||
| タイトル | ||||||
| タイトル | ハイポイドギヤの歯切り誤差検出法 | |||||
| タイトル | ||||||
| タイトル | ハイポイドギヤの歯切り誤差検出法 | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Measuremnent | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Gear | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Hypoid Gear | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Method of Least Squares | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Machine Setting Error | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Gleason Hypoid Generator | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Three-Dimensional Coordinate Measuring Machine | |||||
| 資源タイプ | ||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_5794 | |||||
| 資源タイプ | conference paper | |||||
| その他のタイトル | ||||||
| その他のタイトル | A Method of Detection of Errors in Hypoid Gear Cutting | |||||
| 著者 |
川崎, 一正
× 川崎, 一正× 田村, 久司 |
|||||
| 著者別名 | ||||||
| 識別子Scheme | WEKO | |||||
| 識別子 | 170815 | |||||
| 姓名 | Kawasaki, Kazumasa | |||||
| 著者別名 | ||||||
| 識別子Scheme | WEKO | |||||
| 識別子 | 170816 | |||||
| 姓名 | Tamura, Hisashi | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | A method of the detection of errors in hypoid gear cutting is proposed. The coordinates of the points on the gear tooth surfaces are measured using a three-coordinate measuring machine and the surfaces are estimated by the method of least squares so that the surfaces can fit to the data of coordinate measurements. The surfaces differ from the designed surfaces because of machine setting errors on a Gleason hypoid generator. The purpose of this method is to find the machine setting errors. The coordinates of the points on the gear tooth surfaces were practically measured and the errors were found by this method. Furthermore, the errors were compensated and the corrective cutting was carried out. As a result, the surfaces closing to the designed surfaces could be obtained. The validity was confirmed by the observation of the contact pattern for gear pair. | |||||
| 書誌情報 |
通常総会講演会講演論文集 en : 通常総会講演会講演論文集 巻 930-9, p. 476-478, 発行日 1993 |
|||||
| 出版者 | ||||||
| 出版者 | 日本機械学会 | |||||
| 権利 | ||||||
| 権利情報 | 日本機械学会 | |||||
| 著者版フラグ | ||||||
| 値 | publisher | |||||
