WEKO3
アイテム
工具逃げ面の高精度化による仕上げ面粗さの改善
http://hdl.handle.net/10191/1792
http://hdl.handle.net/10191/1792eea009bf-cc6a-460c-b8ab-a89f0aa18879
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
5_0006.pdf (688.6 kB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2007-05-10 | |||||
| タイトル | ||||||
| タイトル | 工具逃げ面の高精度化による仕上げ面粗さの改善 | |||||
| タイトル | ||||||
| タイトル | 工具逃げ面の高精度化による仕上げ面粗さの改善 | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Cutting Accuracy | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | End Milling | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Surface Roughness | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | High-Accurate Cutting Edge | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Flank Surface | |||||
| キーワード | ||||||
| 主題Scheme | Other | |||||
| 主題 | Roughness Improvement | |||||
| 資源タイプ | ||||||
| 資源 | http://purl.org/coar/resource_type/c_6501 | |||||
| タイプ | journal article | |||||
| その他のタイトル | ||||||
| その他のタイトル | Improvement of Surface Roughness for End Milling using Cutting Edge with High-Accurate Flank Surface | |||||
| 著者 |
岩部, 洋育
× 岩部, 洋育× 大瀬戸, 隆之× 後藤, 隆夫 |
|||||
| 著者別名 | ||||||
| 識別子Scheme | WEKO | |||||
| 識別子 | 45427 | |||||
| 姓名 | Iwabe, Hiroyasu | |||||
| 著者別名 | ||||||
| 識別子Scheme | WEKO | |||||
| 識別子 | 45428 | |||||
| 姓名 | Oseto, Takayuki | |||||
| 著者別名 | ||||||
| 識別子Scheme | WEKO | |||||
| 識別子 | 45429 | |||||
| 姓名 | Goto, Takao | |||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | This paper deals with improvement of the surface roughness for end milling using the cutting edge with a high-accurate flank surface. In usual end milling, it is very difficult to machining a high-accurate surface even if finishing conditions are used, because of the surface machined is copied by the roughness curve of flank surface of a cutting edge. Then it is investigated that the surface roughness of machined surrace in axial direction is improved by high-accurate cutting edges. The main results are as followings. (1) Maximum hight of roughness curve of machined surface in axial direction is almost 10 times as large as that in feed direction. (2) The roughness curve of flank surface of cutting edge was copied on that of machined surface, and the degree of transference is diffined by the mean of the absolute value of defferences of both roughness curves. (3) The maximum hight of roughness curve of a flank surface decreases from 1.71 μm to 0.53 μm of which surface is finished by a diamond wheel. (4) The maximum hight of roughness curve of machined surface decreases drastically from 2.53 μm to 0.58 μm using the above high-accurate cutting edge. | |||||
| 書誌情報 |
日本機械学会論文集. C編 en : 日本機械学会論文集. C編 巻 68, 号 666, p. 650-656, 発行日 2002-02 |
|||||
| 出版者 | ||||||
| 出版者 | 日本機械学会 | |||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 03875024 | |||||
| 書誌レコードID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00187463 | |||||
| 権利 | ||||||
| 権利情報 | 日本機械学会 | |||||
| 著者版フラグ | ||||||
| 値 | publisher | |||||
