{"created":"2021-03-01T06:07:33.945681+00:00","id":3795,"links":{},"metadata":{"_buckets":{"deposit":"c9c5098c-c667-49c1-a13c-47d740d4ae7c"},"_deposit":{"id":"3795","owners":[],"pid":{"revision_id":0,"type":"depid","value":"3795"},"status":"published"},"_oai":{"id":"oai:niigata-u.repo.nii.ac.jp:00003795","sets":["453:454","468:469:470"]},"item_5_alternative_title_1":{"attribute_name":"その他のタイトル","attribute_value_mlt":[{"subitem_alternative_title":"Improvement of Surface Roughness for End Milling using Cutting Edge with High-Accurate Flank Surface"}]},"item_5_biblio_info_6":{"attribute_name":"書誌情報","attribute_value_mlt":[{"bibliographicIssueDates":{"bibliographicIssueDate":"2002-02","bibliographicIssueDateType":"Issued"},"bibliographicIssueNumber":"666","bibliographicPageEnd":"656","bibliographicPageStart":"650","bibliographicVolumeNumber":"68","bibliographic_titles":[{"bibliographic_title":"日本機械学会論文集. C編"},{"bibliographic_title":"日本機械学会論文集. C編","bibliographic_titleLang":"en"}]}]},"item_5_description_4":{"attribute_name":"抄録","attribute_value_mlt":[{"subitem_description":"This paper deals with improvement of the surface roughness for end milling using the cutting edge with a high-accurate flank surface. In usual end milling, it is very difficult to machining a high-accurate surface even if finishing conditions are used, because of the surface machined is copied by the roughness curve of flank surface of a cutting edge. Then it is investigated that the surface roughness of machined surrace in axial direction is improved by high-accurate cutting edges. The main results are as followings. (1) Maximum hight of roughness curve of machined surface in axial direction is almost 10 times as large as that in feed direction. (2) The roughness curve of flank surface of cutting edge was copied on that of machined surface, and the degree of transference is diffined by the mean of the absolute value of defferences of both roughness curves. (3) The maximum hight of roughness curve of a flank surface decreases from 1.71 μm to 0.53 μm of which surface is finished by a diamond wheel. (4) The maximum hight of roughness curve of machined surface decreases drastically from 2.53 μm to 0.58 μm using the above high-accurate cutting edge.","subitem_description_type":"Abstract"}]},"item_5_full_name_3":{"attribute_name":"著者別名","attribute_value_mlt":[{"nameIdentifiers":[{"nameIdentifier":"45427","nameIdentifierScheme":"WEKO"}],"names":[{"name":"Iwabe, Hiroyasu"}]},{"nameIdentifiers":[{"nameIdentifier":"45428","nameIdentifierScheme":"WEKO"}],"names":[{"name":"Oseto, Takayuki"}]},{"nameIdentifiers":[{"nameIdentifier":"45429","nameIdentifierScheme":"WEKO"}],"names":[{"name":"Goto, Takao"}]}]},"item_5_publisher_7":{"attribute_name":"出版者","attribute_value_mlt":[{"subitem_publisher":"日本機械学会"}]},"item_5_rights_15":{"attribute_name":"権利","attribute_value_mlt":[{"subitem_rights":"日本機械学会"}]},"item_5_select_19":{"attribute_name":"著者版フラグ","attribute_value_mlt":[{"subitem_select_item":"publisher"}]},"item_5_source_id_11":{"attribute_name":"書誌レコードID","attribute_value_mlt":[{"subitem_source_identifier":"AN00187463","subitem_source_identifier_type":"NCID"}]},"item_5_source_id_9":{"attribute_name":"ISSN","attribute_value_mlt":[{"subitem_source_identifier":"03875024","subitem_source_identifier_type":"ISSN"}]},"item_creator":{"attribute_name":"著者","attribute_type":"creator","attribute_value_mlt":[{"creatorNames":[{"creatorName":"岩部, 洋育"}],"nameIdentifiers":[{"nameIdentifier":"45424","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"大瀬戸, 隆之"}],"nameIdentifiers":[{"nameIdentifier":"45425","nameIdentifierScheme":"WEKO"}]},{"creatorNames":[{"creatorName":"後藤, 隆夫"}],"nameIdentifiers":[{"nameIdentifier":"45426","nameIdentifierScheme":"WEKO"}]}]},"item_files":{"attribute_name":"ファイル情報","attribute_type":"file","attribute_value_mlt":[{"accessrole":"open_date","date":[{"dateType":"Available","dateValue":"2019-07-30"}],"displaytype":"detail","filename":"5_0006.pdf","filesize":[{"value":"688.6 kB"}],"format":"application/pdf","licensetype":"license_note","mimetype":"application/pdf","url":{"label":"5_0006.pdf","url":"https://niigata-u.repo.nii.ac.jp/record/3795/files/5_0006.pdf"},"version_id":"4196b286-b717-44f4-a96b-5ee4d38161d3"}]},"item_keyword":{"attribute_name":"キーワード","attribute_value_mlt":[{"subitem_subject":"Cutting Accuracy","subitem_subject_scheme":"Other"},{"subitem_subject":"End Milling","subitem_subject_scheme":"Other"},{"subitem_subject":"Surface Roughness","subitem_subject_scheme":"Other"},{"subitem_subject":"High-Accurate Cutting Edge","subitem_subject_scheme":"Other"},{"subitem_subject":"Flank Surface","subitem_subject_scheme":"Other"},{"subitem_subject":"Roughness Improvement","subitem_subject_scheme":"Other"}]},"item_language":{"attribute_name":"言語","attribute_value_mlt":[{"subitem_language":"jpn"}]},"item_resource_type":{"attribute_name":"資源タイプ","attribute_value_mlt":[{"resourcetype":"journal article","resourceuri":"http://purl.org/coar/resource_type/c_6501"}]},"item_title":"工具逃げ面の高精度化による仕上げ面粗さの改善","item_titles":{"attribute_name":"タイトル","attribute_value_mlt":[{"subitem_title":"工具逃げ面の高精度化による仕上げ面粗さの改善"},{"subitem_title":"工具逃げ面の高精度化による仕上げ面粗さの改善","subitem_title_language":"en"}]},"item_type_id":"5","owner":"1","path":["454","470"],"pubdate":{"attribute_name":"公開日","attribute_value":"2007-05-10"},"publish_date":"2007-05-10","publish_status":"0","recid":"3795","relation_version_is_last":true,"title":["工具逃げ面の高精度化による仕上げ面粗さの改善"],"weko_creator_id":"1","weko_shared_id":null},"updated":"2022-12-15T03:36:51.479961+00:00"}