WEKO3
アイテム
熱膨張量推定のためのボールねじ温度分布測定位置の選定
http://hdl.handle.net/10191/27590
http://hdl.handle.net/10191/27590f5db52b1-4713-425a-9a56-78c8ce5f471e
名前 / ファイル | ライセンス | アクション |
---|---|---|
![]() |
|
Item type | 学術雑誌論文 / Journal Article(1) | |||||
---|---|---|---|---|---|---|
公開日 | 2014-06-20 | |||||
タイトル | ||||||
タイトル | 熱膨張量推定のためのボールねじ温度分布測定位置の選定 | |||||
タイトル | ||||||
言語 | en | |||||
タイトル | 熱膨張量推定のためのボールねじ温度分布測定位置の選定 | |||||
言語 | ||||||
言語 | jpn | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | measuring position | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | temperature | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | ball-screw | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | thermal elongation | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | optical telemeter | |||||
資源タイプ | ||||||
資源 | http://purl.org/coar/resource_type/c_6501 | |||||
タイプ | journal article | |||||
その他のタイトル | ||||||
その他のタイトル | Selection of Measuring Position of Ball-screw Temperature Distribution for Estimation of Thermal Elongation | |||||
著者 |
横山, 和宏
× 横山, 和宏× 小寺, 岳彦× 永井, 豊× 鈴木, 孝昌 |
|||||
著者別名 | ||||||
識別子 | 40903 | |||||
識別子Scheme | WEKO | |||||
姓名 | Yokoyama, Kazuhiro | |||||
著者別名 | ||||||
識別子 | 40904 | |||||
識別子Scheme | WEKO | |||||
姓名 | Kodera, Takehiko | |||||
著者別名 | ||||||
識別子 | 40905 | |||||
識別子Scheme | WEKO | |||||
姓名 | Nagai, Yutaka | |||||
著者別名 | ||||||
識別子 | 39 | |||||
識別子Scheme | WEKO | |||||
姓名 | Suzuki, Takamasa | |||||
抄録 | ||||||
内容記述タイプ | Abstract | |||||
内容記述 | The optical telemeter system developed is used to measure the temperature distribution of ball-screw and to estimate the thermal elongation of the ball-screw. This paper deals with the selection policy of the measuring position of the temperature. One of the main heat sources is the contact zone between the groove surface of ball-screw and the rolling ball. It is experimentally examined the temperature distribution right under the groove valley and at other positions of the inner surface of hollow ball-screw. It is clarified that the temperature difference due to measuring position within lead length is less than 0.07℃ under the driving condition less than 20m/min table speed. Thus the every position within lead length is available for the temperature measurement to estimate the thermal elongation of ball-screw. | |||||
書誌情報 |
設計工学 en : 設計工学 巻 41, 号 8, p. 417-422, 発行日 2006-08 |
|||||
出版者 | ||||||
出版者 | 日本設計工学会 | |||||
ISSN | ||||||
収録物識別子タイプ | ISSN | |||||
収録物識別子 | 09192948 | |||||
書誌レコードID | ||||||
収録物識別子タイプ | NCID | |||||
収録物識別子 | AN10402165 | |||||
権利 | ||||||
権利情報 | © 2006 日本設計工学会 | |||||
権利 | ||||||
権利情報 | 本文データは学会の許諾を得て再録したものである | |||||
著者版フラグ | ||||||
値 | publisher |