WEKO3
アイテム
Al-Mg合金の超音波接合性におよぼすマグネシウムの影響 : Al-Mg合金の超音波接合(第1報)
http://hdl.handle.net/10191/6297
http://hdl.handle.net/10191/6297549a6809-7307-42ea-b502-a5eae8e37b0f
名前 / ファイル | ライセンス | アクション |
---|---|---|
06_0015.pdf (1.3 MB)
|
|
Item type | 学術雑誌論文 / Journal Article(1) | |||||
---|---|---|---|---|---|---|
公開日 | 2008-04-23 | |||||
タイトル | ||||||
タイトル | Al-Mg合金の超音波接合性におよぼすマグネシウムの影響 : Al-Mg合金の超音波接合(第1報) | |||||
タイトル | ||||||
タイトル | Al-Mg合金の超音波接合性におよぼすマグネシウムの影響 : Al-Mg合金の超音波接合(第1報) | |||||
言語 | en | |||||
言語 | ||||||
言語 | jpn | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Ultrasonic Welding | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Aluminum alloy | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Magnesium | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Surface segregation | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Oxide film | |||||
資源タイプ | ||||||
資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
資源タイプ | journal article | |||||
その他のタイトル | ||||||
その他のタイトル | Effect of Magnesium on Ultrasonic Weldability of Al-Mg Alloy : Ultrasonic Welding of Al-Mg Alloy (1st Report) | |||||
著者 |
平石, 誠
× 平石, 誠× 渡辺, 健彦 |
|||||
著者別名 | ||||||
識別子Scheme | WEKO | |||||
識別子 | 47925 | |||||
姓名 | Hiraishi, Makoto | |||||
著者別名 | ||||||
識別子Scheme | WEKO | |||||
識別子 | 47926 | |||||
姓名 | Watanabe, Takehiko | |||||
抄録 | ||||||
内容記述タイプ | Abstract | |||||
内容記述 | The behavior of magnesium (Mg) in the ultrasonic welding process of aluminum (Al) alloy containing Mg was investigated to understand the reason for the poor weldability. Commercially pure Al (A1050), Al-2.6 mass% Mg alloy (A5052), and Al-4.1 mass% Mg alloy (A5086), 1.2mm thick each, were lap-welded and the fracture surfaces were examined by SEM observation and AES analysis. For all of these materials, the tensile load of the weld increased with an increase in the clamping load or in the welding time. In the case of Al-Mg alloys, higher Mg concentration required higher clamping load or longer welding time to obtain the tensile load equivalent to A1050. SEM observation of the fracture surface of the weld indicated that dimple pattern occupied the almost whole fracture surface of A1050. On the other hand, upon Al-Mg alloys, scraped fracture pattern, dimple pattern and brittle fracture pattern were observed and the scraped pattern occupied the largest area in the fracture surface. AES analysis of each fracture surface showed that Mg was segregated at the surface presenting the scraped and the brittle pattern. Especially at the scraped pattern surface, welding for short time of 0.5s induced the segregation of Mg about twice as high as the concentration before welding. When the specimen having the surface segregation of Mg formed by the pre-heat treatment was welded, the scraped pattern was observed on the almost whole fracture surface and the tensile load of the weld decreased. Conclusively, it was found out that the surface segregation of Mg induced during the process of the welding caused the ultrasonic weldability of Al-Mg alloy to deteriorate. | |||||
書誌情報 |
溶接学会論文集 en : 溶接学会論文集 巻 20, 号 4, p. 552-558, 発行日 2002 |
|||||
出版者 | ||||||
出版者 | 溶接学会 | |||||
ISSN | ||||||
収録物識別子タイプ | ISSN | |||||
収録物識別子 | 02884771 | |||||
書誌レコードID | ||||||
収録物識別子タイプ | NCID | |||||
収録物識別子 | AN1005067X | |||||
著者版フラグ | ||||||
値 | publisher |