WEKO3
アイテム
エンドミルによるコーナ加工の精度改善に関する研究
http://hdl.handle.net/10191/1790
http://hdl.handle.net/10191/1790f458af47-57c6-47d4-80cb-9bf494867dd5
名前 / ファイル | ライセンス | アクション |
---|---|---|
5_0002.pdf (628.6 kB)
|
|
Item type | 学術雑誌論文 / Journal Article(1) | |||||
---|---|---|---|---|---|---|
公開日 | 2007-05-10 | |||||
タイトル | ||||||
タイトル | エンドミルによるコーナ加工の精度改善に関する研究 | |||||
タイトル | ||||||
タイトル | エンドミルによるコーナ加工の精度改善に関する研究 | |||||
言語 | en | |||||
言語 | ||||||
言語 | jpn | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Milling | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Cutting Tool | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Adaptive Control | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Numerical Control | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | End Mill | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Cornering Cut | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Chip Area | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Cutting Method | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Machining Accuracy | |||||
キーワード | ||||||
主題Scheme | Other | |||||
主題 | Depth of Cut | |||||
資源タイプ | ||||||
資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||
資源タイプ | journal article | |||||
その他のタイトル | ||||||
その他のタイトル | Study on Improvement of Machining Accuracy in Cornering Cut with End Mill | |||||
著者 |
李, 勇
× 李, 勇× 岩部, 洋育× 藤井, 義也 |
|||||
著者別名 | ||||||
識別子Scheme | WEKO | |||||
識別子 | 46049 | |||||
姓名 | Li, Yong | |||||
著者別名 | ||||||
識別子Scheme | WEKO | |||||
識別子 | 46050 | |||||
姓名 | Iwabe, Hiroyasu | |||||
著者別名 | ||||||
識別子Scheme | WEKO | |||||
識別子 | 46051 | |||||
姓名 | Fujii, Yoshiya | |||||
抄録 | ||||||
内容記述タイプ | Abstract | |||||
内容記述 | It has been noted that the deflection of the end mill and workpiece produced by the cutting force is a main cause of surface error in the end milling process. The deflection, therefore surface error, becomes even worse in the case of inner cornering cut. To improve machining accuracy, a predictive analysis on the behavior of the cutting force is performed indirectly by means of chip area. Based on the analysis, cutting methods with decreased axial depth of cut or improved shape of the finishing surface in the preceding cut are proposed. Also constraint adaptive control is considered for the rapid variance in cutting force. Through experiments, the effectiveness of the cutting methods and adaptive control in decreasing the error in the corner is acertained. | |||||
書誌情報 |
日本機械学会論文集. C編 en : 日本機械学会論文集. C編 巻 56, 号 532, p. 3444-3449, 発行日 1990-12 |
|||||
出版者 | ||||||
出版者 | 日本機械学会 | |||||
ISSN | ||||||
収録物識別子タイプ | ISSN | |||||
収録物識別子 | 03875024 | |||||
書誌レコードID | ||||||
収録物識別子タイプ | NCID | |||||
収録物識別子 | AN00187463 | |||||
権利 | ||||||
権利情報 | 日本機械学会 | |||||
著者版フラグ | ||||||
値 | publisher |