@article{oai:niigata-u.repo.nii.ac.jp:00025680, author = {Shigetani, Yoshimi and Tate, Yasuaki and Okamoto, Akira and Abu-Bakr, Neamat and Iwaku, Masaaki and Kota, Kohichi}, issue = {1}, journal = {新潟歯学会雑誌, 新潟歯学会雑誌}, month = {Jul}, note = {The purpose of this study was to evaluate microstructure of adhesive interface after removal caries by Er : YAG laser. Observation of the micromorophology of adhesive interface was performed by Laser Scanning Microscope (LSM), Scanning Electron Microscope (SEM) and WDX type of electron probe X-ray microanalyzer (EPMA). The results were as follows: 1. LSM images on the enamel and dentin cutting surfaces filled by composite resin system The surface of the enamel cut by the Er : YAG laser system was showing a crack. While surface cut by an air-turbine hand piece was not showing a crack. 2. EPMA Analysis on the enamel or dentin interface filled by composite resin system In SEM image, the cavity prepared by the laser had crack in the enamel. While the cavity prepared by turbine had hardly any cracks. When observed under an SEM, peripheral irregularities were more marked in the laser cut group than in the turbine cut group. The cavity prepared by the laser and turbine showed no cracks in the dentin. EPMA images showed that the decrease of calcium and phosphorus on the enamel and dentin area irradiated by Er : YAG laser were more remarkable than that on surfaces prepared by air-turbine handpiece. The results of the present investigation suggested that the subsurface layers of the enamel and dentin area irradiated by Er : YAG laser were mechanically weakened due to the formation of structural defects and denatured layer, leading to considerably lower adhesive properties of resin bonding systems., 本研究では、レーザー照射歯面におけるコンポジットレジンの接着機構を明らかにすることを目的として、Er : YAGレーザーによるう触除去後の接着界面の検討を行った。接着界面の観察は、走査型共焦点レーザー顕微鏡(LSM)およびⅩ線マイクロアナライザー(EPMA)を用いて行われた。 1.コンポジットレジン充填後の歯質切削面のLSMによる観察 エナメル質において、Er : YAGレーザーによる形成窩洞には、クラックが認められたが、タービンを用いた場合には、クラックは認められなかった。象牙質では、Er : YAGレーザーおよびタービンを用いた形成窩洞とも、クラックは認められなかった。 2.コンポジットレジン充填後の接着界面のⅩ線マイクロアナライザーによる観察 SEM像において、Er : YAGレーザーによるエナメル質形成窩洞には、クラックが認められたが、タービンを用いた場合には、クラックは認められなかった。形成窩洞の辺縁は、タービンを用いたものより、レーザーを用いた方が、明らかに不規則であった。象牙質では、Er : YAGレーザーおよびタービンを用いた形成窩洞においては、共に、クラックは認められなかった。EPMA像において、エナメル質および象牙質とも、タービンを用いた形成窩洞よりレーザーを用いた方が、CaとPの濃度の低下を認めた。以上の結果から、Er : YAGレーザー照射により、エナメル質および象牙質表層に、コンポジットレジンの接着性を阻害する構造の欠陥や変性層が生ずることが示唆された。}, pages = {49--55}, title = {Study on Microstructure of Adhesive Interface after Caries Removal by Er : YAG laser}, volume = {33}, year = {2003} }